Known failures at solidcore adf26ddbc: curvature and variable rounds built

The rig on solidcore: 982/1014 pass (968 at pin 13). Fourteen cases
come off the lists (the curvature rounds, the variable cone, 3604's G2
swept tool, the curvature fillet after a fillet). Six remain with new
causes: the G2 pocket corner and the bar corner's three edges (two) G1
at one seam and the cylinder-side G2 corner not closed, as on SMLib;
the oblique three-edge corner refused for its mixed wedges; the mixed
corner refused as on SMLib.

Tests (nextest, ci profile, PR filter): 34 come off
KNOWN_FAILING_TESTS (curvature and variable rounds). three_rounds_at_a_corner
is listed (its corner's variable transition at 0.144°, as on SMLib
d01d7b0); chord_and_variable_fillets now fails on its waist law's
corner (solidcore#430).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01SdcgEu4Lr3moCCisdZShKz

tests/KNOWN_FAILING_TESTS

@@ -7,53 +7,20 @@
 # --list). Refresh as that list's header says.
 solidcraft-cli::action_matrix::action_matrix_sample 3 baseline actions fail, the same 3 as on C++: 2 shells (Bad Loop Orient on issue-616-lid-ribs; status 1001 on filleted-shelled-box), 1 fillet (SmSurfOfRevolution Test #7 on oblique_cut_of_cylinder)
 solidcraft-cli::naming_corpus::corpus_designs_name_alike_every_build_and_fail_where_a_reference_is_gone oracle/83-boundary-loop-thicken does not load: step 8, thicken status 1001, as on C++
-solidcraft-engine::cmd::edit::tests::g2_fillet_survives_edit_undo_and_reopen solidcore refuses the curvature fillet until it has the curvature section's equal-area Gⁿ generator (solidcore#2250, port in progress as #2260); SMLib d01d7b0 builds it
 solidcraft-engine::cmd::edit::tests::inserting_variable_fillet_control_preserves_parameters_at_existing_positions solidcore refuses a variable fillet whose law has a corner (solidcore#430)
-solidcraft-engine::cmd::edit::tests::redefining_a_fillet_as_g2_on_sloped_ends_survives_undo_and_reopen solidcore refuses the curvature fillet until it has the curvature section's equal-area Gⁿ generator (solidcore#2250, port in progress as #2260); SMLib d01d7b0 builds it
 solidcraft-engine::cmd::sketch::face::tests::a_sketch_on_the_ring_of_a_lid_underside_parted_by_its_lip_keeps_the_cap main's test: the ring is named F14:start#[...], the lid's own start, not F2:top, the case's top it rests on, so the lookup finds no ring, as on C++
 solidcraft-engine::cmd::sketch::ids_tests::a_curve_id_that_cannot_be_written_into_a_name_is_refused main's test: an extruded circle has a seam edge, the side face on both its sides, named F2:side:c1 with no second face, as on C++
-solidcraft-engine::cmd::sketch_project::tests::a_free_form_edge_projects_as_one_spline_with_its_own_knots its fixture's g2 fillet: solidcore refuses the curvature fillet until it has the curvature section's equal-area Gⁿ generator (solidcore#2250, port in progress as #2260); SMLib d01d7b0 builds it
-solidcraft-engine::tests::chord_and_variable_fillets solidcore refuses a variable-radius fillet until it builds the round as the union of its balls (smlib#78; solidcore#2250, port in progress as #2262); SMLib d01d7b0 builds it
+solidcraft-engine::tests::chord_and_variable_fillets its 2 → 4 → 2 waist: solidcore refuses a variable fillet whose law has a corner (solidcore#430)
 solidcraft-engine::tests::fillet_fit_taper_closes_to_a_point fillet status 1001 on the taper fit (radius 16 closing to 0), as on C++
-solidcraft-engine::tests::fillet_fit_taper_follows_the_room_along_the_edge solidcore refuses a variable-radius fillet until it builds the round as the union of its balls (smlib#78; solidcore#2250, port in progress as #2262); SMLib d01d7b0 builds it
-solidcraft-engine::tests::spline_fillet_takes_over_a_taper solidcore refuses a variable-radius fillet until it builds the round as the union of its balls (smlib#78; solidcore#2250, port in progress as #2262); SMLib d01d7b0 builds it
 solidcraft-kernel::blend::corner_tests::a_round_ending_in_an_earlier_round_matches_both_together fillet status 1001 on the round that ends in the earlier one, as on C++
 solidcraft-kernel::blend::corner_tests::corner_blends_hold_at_any_scale at 0.01x the arc case's rounds remove 72.783 (scaled back) against 72.713 at 1x, as on C++
-solidcraft-kernel::blend::tests::g2_fillet_handles_concave_edges_and_separate_edges solidcore refuses the curvature fillet until it has the curvature section's equal-area Gⁿ generator (solidcore#2250, port in progress as #2260); SMLib d01d7b0 builds it
-solidcraft-kernel::blend::tests::g2_fillet_meets_sloped_planar_ends solidcore refuses the curvature fillet until it has the curvature section's equal-area Gⁿ generator (solidcore#2250, port in progress as #2260); SMLib d01d7b0 builds it
-solidcraft-kernel::blend::tests::g2_fillet_on_concave_edge_meets_caps_sloped_in_both_directions solidcore refuses the curvature fillet until it has the curvature section's equal-area Gⁿ generator (solidcore#2250, port in progress as #2260); SMLib d01d7b0 builds it
-solidcraft-kernel::blend::tests::g2_fillet_refuses_invalid_geometry its wide fillet over the cliffs: solidcore refuses the curvature fillet until it has the curvature section's equal-area Gⁿ generator (solidcore#2250, port in progress as #2260); SMLib d01d7b0 builds it
-solidcraft-kernel::blend::tests::g2_fillet_refuses_sections_crossing_a_cap_hole solidcore refuses the curvature fillet until it has the curvature section's equal-area Gⁿ generator (solidcore#2250, port in progress as #2260); SMLib d01d7b0 builds it
-solidcraft-kernel::blend::tests::g2_fillet_takes_off_what_the_round_does solidcore refuses the curvature fillet until it has the curvature section's equal-area Gⁿ generator (solidcore#2250, port in progress as #2260); SMLib d01d7b0 builds it
 solidcraft-kernel::blend_corner::tests::issue2422_vertical_after_separate_bottom_rounds the check refuses the fillet: edge and vertex tolerance 0.97 against the body's 0.01, as on C++ (#2422)
-solidcraft-kernel::blend_smlib::tests::a_linear_radius_runs_from_the_start_end solidcore refuses a variable-radius fillet until it builds the round as the union of its balls (smlib#78; solidcore#2250, port in progress as #2262); SMLib d01d7b0 builds it
-solidcraft-kernel::blend_variable::taper_mesh_tests::collapsed_taper_mesh_stays_accurate_as_tolerance_decreases solidcore refuses a variable-radius fillet until it builds the round as the union of its balls (smlib#78; solidcore#2250, port in progress as #2262); SMLib d01d7b0 builds it
-solidcraft-kernel::blend_variable::taper_mesh_tests::the_wedge_round_keeps_its_volume solidcore refuses a variable-radius fillet until it builds the round as the union of its balls (smlib#78; solidcore#2250, port in progress as #2262); SMLib d01d7b0 builds it
-solidcraft-kernel::blend_variable::tests::taper_follows_the_room_along_the_edge solidcore refuses a variable-radius fillet until it builds the round as the union of its balls (smlib#78; solidcore#2250, port in progress as #2262); SMLib d01d7b0 builds it
-solidcraft-kernel::blend_variable::tests::variable_radius_down_to_zero_at_one_end solidcore refuses a variable-radius fillet until it builds the round as the union of its balls (smlib#78; solidcore#2250, port in progress as #2262); SMLib d01d7b0 builds it
-solidcraft-kernel::blend_variable::tests::variable_radius_from_a_spline solidcore refuses a variable-radius fillet until it builds the round as the union of its balls (smlib#78; solidcore#2250, port in progress as #2262); SMLib d01d7b0 builds it
-solidcraft-kernel::blend_variable::tests::variable_radius_on_a_box_edge solidcore refuses a variable-radius fillet until it builds the round as the union of its balls (smlib#78; solidcore#2250, port in progress as #2262); SMLib d01d7b0 builds it
-solidcraft-kernel::blend_variable::tests::variable_radius_through_a_middle_point solidcore refuses a variable-radius fillet until it builds the round as the union of its balls (smlib#78; solidcore#2250, port in progress as #2262); SMLib d01d7b0 builds it
+solidcraft-kernel::blend_corner::tests::three_rounds_at_a_corner the corner's variable-radius transition between rounds of different radii meets its neighbours at 0.144 degrees once its sections are the balls' touch circles (fillet_gn_section_generator, solidcore#2262; 0 with the great circles), as on SMLib d01d7b0; the corner step replaces that transition
 solidcraft-kernel::blend_variable::tests::variable_radius_with_a_corner_through_a_middle_point solidcore refuses a variable fillet whose law has a corner (solidcore#430)
 solidcraft-kernel::corner_g2::tests::a_long_setback_keeps_the_g2_patch_inside_the_box at set backs 11 to 15 the G2 corner patch bulges past the box, as on C++
-solidcraft-kernel::corner_g2::tests::curvature_rounds_meet_at_a_g2_corner solidcore refuses the curvature fillet until it has the curvature section's equal-area Gⁿ generator (solidcore#2250, port in progress as #2260); SMLib d01d7b0 builds it
 solidcraft-kernel::corner_g2::tests::the_box_corner_g2_patch_is_a_closed_solid_curvature_continuous_to_its_neighbours the fitted G2 corner patch bulges 1.7e-5 past the box, as on C++
-solidcraft-kernel::modify_history_tests::fillet_variable_and_chord solidcore refuses a variable-radius fillet until it builds the round as the union of its balls (smlib#78; solidcore#2250, port in progress as #2262); SMLib d01d7b0 builds it
 solidcraft-kernel::tests::fillet_tabbed_plate_outer_loop_and_partial_selection_after_hole each tab corner arc rounds alone since solidcore#2176, but the R25 rim and a corner arc picked together fail 1001 in cliff_overflow (no room), though each builds alone; on C++ the rounds together miss by 3.8e-4 (solidcore#2223)
-solidcraft-smlib::core::blend_tests::fillet_curvature_one_edge::solidcore_matches_the_closed_form solidcore refuses the curvature fillet until it has the curvature section's equal-area Gⁿ generator (solidcore#2250, port in progress as #2260); SMLib d01d7b0 builds it
-solidcraft-smlib::core::blend_tests::fillet_curvature_one_edge::solidcore_matches_the_cpp_kernel solidcore refuses the curvature fillet until it has the curvature section's equal-area Gⁿ generator (solidcore#2250, port in progress as #2260); SMLib d01d7b0 builds it
-solidcraft-smlib::core::blend_tests::fillet_variable_linear::solidcore_matches_the_closed_form solidcore refuses a variable-radius fillet until it builds the round as the union of its balls (smlib#78; solidcore#2250, port in progress as #2262); SMLib d01d7b0 builds it
-solidcraft-smlib::core::blend_tests::fillet_variable_linear::solidcore_matches_the_cpp_kernel solidcore refuses a variable-radius fillet until it builds the round as the union of its balls (smlib#78; solidcore#2250, port in progress as #2262); SMLib d01d7b0 builds it
 solidcraft-smlib::core::offset_tests::mitred_rounds_follow_a_moved_top the C++ comparison: solidcore's offset edges keep their tolerances (offset_edges_keep_source_tolerance, solidcore#2111), C++ at 7ac037e's do not, so the moved tops' volumes are 2e-9 to 2.3e-7 apart; both are 1.2e-8 to 3.1e-7 off the closed form at accuracy 1e-8, solidcore with the fix 2.1e-7 at most
-solidcraft-smlib::export::tests::native_tests::a_nurbs_edge_interval_a_rounding_past_its_knots_is_moved_onto_them solidcore refuses a variable-radius fillet until it builds the round as the union of its balls (smlib#78; solidcore#2250, port in progress as #2262); SMLib d01d7b0 builds it
-solidcraft-smlib::ops::tests::a_variable_round_follows_its_law solidcore refuses a variable-radius fillet until it builds the round as the union of its balls (smlib#78; solidcore#2250, port in progress as #2262); SMLib d01d7b0 builds it
 solidcraft-smlib::ops::tests::a_variable_round_with_a_corner_in_its_law_is_its_balls_union solidcore refuses a variable fillet whose law has a corner (solidcore#430)
-solidcraft-ui-egui::fillet_spline_handle_tests::a_taper_over_several_edges_keeps_the_radius_arrow solidcore refuses a variable-radius fillet until it builds the round as the union of its balls (smlib#78; solidcore#2250, port in progress as #2262); SMLib d01d7b0 builds it
-solidcraft-ui-egui::fillet_spline_handle_tests::double_clicks_add_and_remove_control_radii solidcore refuses a variable-radius fillet until it builds the round as the union of its balls (smlib#78; solidcore#2250, port in progress as #2262); SMLib d01d7b0 builds it
-solidcraft-ui-egui::fillet_spline_handle_tests::dragging_a_taper_handle_makes_the_fillet_a_spline solidcore refuses a variable-radius fillet until it builds the round as the union of its balls (smlib#78; solidcore#2250, port in progress as #2262); SMLib d01d7b0 builds it
-solidcraft-ui-egui::fillet_spline_handle_tests::every_edge_of_a_spline_fillet_has_handles_for_its_one_spline solidcore refuses a variable-radius fillet until it builds the round as the union of its balls (smlib#78; solidcore#2250, port in progress as #2262); SMLib d01d7b0 builds it
-solidcraft-ui-egui::preselect_tests::curvature_canvas_value_uses_equivalent_radius_when_created_and_reopened solidcore refuses the curvature fillet until it has the curvature section's equal-area Gⁿ generator (solidcore#2250, port in progress as #2260); SMLib d01d7b0 builds it
-solidcraft-ui-egui::preselect_tests::variable_fillet_mid_radii_round_trip solidcore refuses a variable-radius fillet until it builds the round as the union of its balls (smlib#78; solidcore#2250, port in progress as #2262); SMLib d01d7b0 builds it
-solidcraft-ui-egui::preselect_tests::variable_fillet_round_trip solidcore refuses a variable-radius fillet until it builds the round as the union of its balls (smlib#78; solidcore#2250, port in progress as #2262); SMLib d01d7b0 builds it
 solidcraft-ui-egui::timeline::tests::each_chip_finds_its_own_result main's test: its radius 20 fillet with fit reduce on a 10 mm box builds without a reduced-radius warning, so the fixture has no warned feature, as on C++
 solidcraft-ui-egui::viewport::appearance_tests::bodies_out_of_the_view_are_not_drawn main's test counts 12 triangles a box; the kernel's mesher gives a 10 mm box more, so the count is wrong before it reaches the culling, as on C++

tests/kernel-cases/booleans/KNOWN_FAILING.solidcore

@@ -1,4 +1,3 @@
 # The booleans cases that fail today on solidcore, one a line: `<case> <why it fails today>`. Sorted.
 # The kernel rig gate fails on a case that fails and is not listed, and on a listed case that passes.
 # Baseline: solidcore pin de85a3e00, tests/kernel-cases run by `cargo xtask kernel-cases`, x86_64 Linux.
-3604-cut-with-g2-swept-tool-along-projected-edge [unsupported] refused on solidcore: the curvature section's equal-area Gn generator (fork 6148773) is not in solidcore yet (solidcore#2250, port in progress as #2260); SMLib d01d7b0 builds it

tests/kernel-cases/fillets/KNOWN_FAILING.solidcore

@@ -5,43 +5,30 @@
 1080-fillet-sloped-basin-1-mm-rim-r4-2-edges [fail] continuity_order: got {'body': 'Slab', 'edges': 'blend', 'order': 'g0',  want >= g1 at every blend seam
 1080-fillet-sloped-basin-1-mm-rim-r4-4-edges [fail] continuity_order: got {'body': 'Slab', 'edges': 'blend', 'order': 'g0',  want >= g1 at every blend seam
 1207-fillet-bar-top-edge-after-boss-arc-round-r0-5 [fail] step 4 (solid.fillet): body `Arm`: the operation failed: SMLib fillet: SMLib's check refuses the result: 5 failed tests: SmBSplineCurve::Test #15 Bad Repeated CPts: BSplineCurve has Internal Coincident ControlPoints (causes
-2708-fillet-curvature-continuous-angled-ends [unsupported] refused on solidcore: the curvature section's equal-area Gn generator (fork 6148773) is not in solidcore yet (solidcore#2250, port in progress as #2260); SMLib d01d7b0 builds it
 2893-chamfer-distance-and-angle-past-the-wall-refused [fail] refused, but not because "angle": step 2 (solid.chamfer): SMLib chamfer: operation: SMLib rejected the input (SM_ERR_INVALID_INPUT)
 2893-chamfer-two-distances-elliptical-rim [fail] refused, but not because "not supported yet": step 3 (solid.chamfer): SMLib chamfer: operation: SMLib failed (status 1001) (tangent propagation blended the picked edges' tangent chain with them; with it off, tangent_chain: 
 4782-fillet-bar-edge-wider-than-both-faces [fail] continuity_order: got Box: no null seams want >= g1 at every blend seam
 5158-fillet-round-just-past-a-10mm-face [fail] step 2 (solid.fillet): SMLib fillet: operation: SMLib failed (status 1001)
-862-fillet-curvature-continuous-box-edge [unsupported] refused on solidcore: the curvature section's equal-area Gn generator (fork 6148773) is not in solidcore yet (solidcore#2250, port in progress as #2260); SMLib d01d7b0 builds it
 9-fillet-corner-curvature-with-reduce-fit [unsupported] solid.fillet builds `corner: g2` with `fit: exact` only
 9-fillet-corner-curvature-with-taper-fit [unsupported] solid.fillet builds `corner: g2` with `fit: exact` only
-cov-fillet-g2-corner-beside-a-cylinder [unsupported] refused on solidcore: the curvature section's equal-area Gn generator (fork 6148773) is not in solidcore yet (solidcore#2250, port in progress as #2260); on SMLib its open setback corner is not a closed solid
+cov-fillet-g2-corner-beside-a-cylinder [fail] step 6 (solid.fillet): the open setback corner is not a closed solid, as on SMLib d01d7b0
 cov-fillet-g2-five-edge-apex-corner [fail] step 12 (solid.fillet): invalid input: the setback must be more than 3.5056 mm at the corner (-0.000, 0.000, 30.000): the rounds' contact lines meet 3
 cov-fillet-g2-four-edge-apex-corner [fail] step 11 (solid.fillet): invalid input: the setback must be more than 3.9027 mm at the corner (0.000, 0.000, 30.000): the rounds' contact lines meet 3.
-cov-fillet-g2-mixed-corner [unsupported] refused on solidcore: the curvature section's equal-area Gn generator (fork 6148773) is not in solidcore yet (solidcore#2250, port in progress as #2260); SMLib refuses its mixed-convexity setback corner
-cov-fillet-g2-oblique-three-edge-corner [unsupported] refused on solidcore: the curvature section's equal-area Gn generator (fork 6148773) is not in solidcore yet (solidcore#2250, port in progress as #2260); SMLib d01d7b0 fails it too (see KNOWN_FAILING)
-cov-fillet-g2-pocket-corner [unsupported] refused on solidcore: the curvature section's equal-area Gn generator (fork 6148773) is not in solidcore yet (solidcore#2250, port in progress as #2260); SMLib d01d7b0 fails it too (see KNOWN_FAILING)
-cov-fillet-section-curvature-boss-root-r2 [unsupported] refused on solidcore: the curvature section's equal-area Gn generator (fork 6148773) is not in solidcore yet (solidcore#2250, port in progress as #2260); SMLib d01d7b0 builds it
-cov-fillet-section-curvature-box-edge-r3 [unsupported] refused on solidcore: the curvature section's equal-area Gn generator (fork 6148773) is not in solidcore yet (solidcore#2250, port in progress as #2260); SMLib d01d7b0 builds it
-cov-fillet-section-curvature-pipe-on-plate-r2 [unsupported] refused on solidcore: the curvature section's equal-area Gn generator (fork 6148773) is not in solidcore yet (solidcore#2250, port in progress as #2260); SMLib d01d7b0 builds it
+cov-fillet-g2-mixed-corner [unsupported] refused as on SMLib d01d7b0: a G2 corner is set back only where every edge meeting it is rounded and all are convex or all concave
+cov-fillet-g2-oblique-three-edge-corner [unsupported] refused on solidcore: its three edges meet at different wedge angles, and one curvature fillet takes the first edge's equal-area thumbweight for every edge (solidcore#2250, issuecomment-6563419897); SMLib d01d7b0 fails it too (see KNOWN_FAILING)
+cov-fillet-g2-pocket-corner [fail] continuity_order: G1 at one seam where the corner patch meets a contact face (g2 wanted), as on SMLib d01d7b0 (see KNOWN_FAILING)
 cov-fillet-turn-swept-boss-base-r1 [fail] as on SMLib: solid.fillet has no `turn`; the corners are mitred (12508.9675, the Mitre case's volume)
 cov-fillet-turn-swept-pocket-sharp-corner-refused-r1 [fail] as on SMLib: solid.fillet has no `turn`, so the sharp concave corners are mitred, not refused
-cov-fillet-variable-box-edge-1-to-5-on-its-cone [unsupported] refused on solidcore: a variable round is the union of its balls (smlib#78 6b346f6, 5db8feb, fb5c060), which solidcore does not build yet (solidcore#2250, port in progress as #2262); SMLib d01d7b0 builds it
 cov-junction-boss-tilt-20-root-round [fail] fillet status 1001 on a cylinder tilted 20 degrees into the plate, as on SMLib
 cov-junction-boss-tilt-40-root-round [fail] fillet status 1001 on a cylinder tilted 40 degrees into the plate, as on SMLib
 cov-junction-tee-equal-round [fail] the result is not a closed solid, as on SMLib: equal pipes' intersection is two plane ellipses crossing, a corner the old corner code cannot join (the corner step)
 cov-junction-y-junction-120-round [unsupported] refused as on SMLib: the faces between the three intersection curves narrow to nothing at the two triple points, so the room check trips (the corner step)
-every-block-cylinder-crease-block-top-edge-r2-curvature [unsupported] refused on solidcore: the curvature section's equal-area Gn generator (fork 6148773) is not in solidcore yet (solidcore#2250, port in progress as #2260); SMLib d01d7b0 builds it
-every-box-edge-r3-curvature [unsupported] refused on solidcore: the curvature section's equal-area Gn generator (fork 6148773) is not in solidcore yet (solidcore#2250, port in progress as #2260); SMLib d01d7b0 builds it
-every-fillet-after-fillet-curvature-front-then-side-r3 [fail] refused before it reaches the tangent continuation: the first curvature fillet is refused on solidcore: the curvature section's equal-area Gn generator (fork 6148773) is not in solidcore yet (solidcore#2250, port in progress as #2260); SMLib d01d7b0 builds it
-every-hole-top-rim-r1-curvature [unsupported] refused on solidcore: the curvature section's equal-area Gn generator (fork 6148773) is not in solidcore yet (solidcore#2250, port in progress as #2260); SMLib d01d7b0 builds it
-every-l-bracket-inside-bend-r3-curvature [unsupported] refused on solidcore: the curvature section's equal-area Gn generator (fork 6148773) is not in solidcore yet (solidcore#2250, port in progress as #2260); SMLib d01d7b0 builds it
 report-drafted-peg-front-and-concave-rounds-together-r2 [unsupported] step 13 (solid.fillet): invalid input: not supported yet: the fillet meets a corner of this kind, which SMLib's blends do not handle yet (where its ed
 report-fillet-concave-arc-and-front-top-edge-together-r5-solver-residues [fail] bbox.min: got [0.4892940775280783, 0.05636444090890084, 0.0] want [0.4892940775280783, 0.05792545052986289, 0.0]
 report-fillet-concave-arc-and-front-top-edge-together-r7-solver-residues [fail] bbox.min: got [0.4892940775169876, 0.02441657049978923, 0.0] want [0.4892940775280783, 0.05792545052986289, 0.0]
-report-fillet-curvature-three-edges-at-bar-corner [unsupported] refused on solidcore: the curvature section's equal-area Gn generator (fork 6148773) is not in solidcore yet (solidcore#2250, port in progress as #2260); SMLib d01d7b0 fails it too (see KNOWN_FAILING)
-report-fillet-curvature-three-edges-at-bar-corner-solver-residues [unsupported] refused on solidcore: the curvature section's equal-area Gn generator (fork 6148773) is not in solidcore yet (solidcore#2250, port in progress as #2260); SMLib d01d7b0 fails it too (see KNOWN_FAILING)
-report-fillet-curvature-three-edges-at-bar-corner-solver-residues-outside-setback [unsupported] refused on solidcore: the curvature section's equal-area Gn generator (fork 6148773) is not in solidcore yet (solidcore#2250, port in progress as #2260); SMLib d01d7b0 builds it
+report-fillet-curvature-three-edges-at-bar-corner [fail] continuity_order: G1 at one seam where the corner patch meets a contact face (g2 wanted), as on SMLib d01d7b0 (see KNOWN_FAILING)
+report-fillet-curvature-three-edges-at-bar-corner-solver-residues [fail] continuity_order: G1 at one seam where the corner patch meets a contact face (g2 wanted), as on SMLib d01d7b0 (see KNOWN_FAILING)
 report-peg-front-and-concave-chamfers-together-d2 [fail] step 13 (solid.chamfer): SMLib chamfer: operation: SMLib failed (status 1001)
 report-peg-front-and-concave-rounds-together-r2 [fail] continuity_order: got {'body': 'Peg', 'edges': 'blend', 'order': 'g0', ' want >= g1 at every blend seam
 report-peg-front-and-concave-rounds-together-r5 [fail] continuity_order: got {'body': 'Peg', 'edges': 'blend', 'order': 'g0', ' want >= g1 at every blend seam
-report-peg-front-curvature-round-r2 [unsupported] refused on solidcore: the curvature section's equal-area Gn generator (fork 6148773) is not in solidcore yet (solidcore#2250, port in progress as #2260); SMLib d01d7b0 builds it
 report-peg-step-front-and-concave-rounds-together-r2 [fail] continuity_order: got {'body': 'Peg', 'edges': 'blend', 'order': 'g0', ' want >= g1 at every blend seam