* Fix recovery for unsaved background tabs (#2884)
* Recovery: scheduled autosaves of every tab write on the worker thread (#2884)
After #3139, Autosaver::save waits for the write and Autosaver::tick runs
it on a worker. The scheduled path now goes through tick (which skips a
tab whose previous write is still running), so several dirty tabs no
longer write on the window thread each interval (#3044). save stays for
Save, close and shutdown. Each tab's autosaver has no clock of its own:
the shared cadence decides when it is due. The tests wait for the
writes a tick started.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Recovery: closing a tab waits for its running autosave before removing the entry (#2884)
With the autosave on a worker thread, discard could remove the files and
the lock while a write was still running; the write then recreated the
entry without a lock, and the next launch offered a design closed with
Don't Save. discard now ends the running write first, as Drop does.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* ui: spacing, radius and type tokens, per-tab accents, agent and on-accent tokens
* ui: per-tab accent behaviour and a larger application bar with a Start page button
* icons: silhouette master and flat assistant and agent link icons (open for review)
* icons: apply review notes (sparkle assistant, refined plug, silhouette halo)
* icons: wire the silhouette master to inspect.silhouette; record the accepted icons
* ui: application bar to the design: separators, Save, house, assistant icon, readable hovers
* ui: ribbon structure: Model to View tabs, contextual Sketch and Sheet Metal, migrated pins
* ui: ribbon painting to the compact design
* ui: smaller icon button highlight and assistant mark on the bubble corner
* ui: short ribbon labels that wrap at spaces
* ui: ribbon buttons fit their labels and Finish Sketch shows its full name
* ui: constraint gallery, workspace menu, section list headings and richer tooltips
* ui: lighter selected tab label, ribbon surface and dimmer bar separators match the dark design
* ui: document tabs as rounded chips with a dimmer inactive label
* ui: document tabs fit their names and show close only when active or hovered
* icons: close and plus masters for the document tabs (open for review)
* ui: centre the new-tab plus and overflow button on the bar
* ui: a quiet rule under the ribbon tabs on non-contextual tabs
* ui: the application bar mark separates its faces with the bar colour, not white
* ui: open ribbon section label uses the selected tint and a chevron
* ui: dim the tab close and plus icons until hovered
* ui: every ribbon dropdown uses the chevron, the workspace card included
* ui: the active document tab uses the design's surface colour
* ui: the bug button's right padding mirrors its icon side
* ui: square constraint cells and a rule before the grid
* ui: constraint cells back to their earlier size, keeping the rule
* ui: smaller constraint cells and icons, centred in the section
* ui: constraint cells fit the height of the large buttons' icon and label
* ui: sketch Create titles share the other labels' line
* ui: format the application bar and ribbon changes
* ui: active tab surface token and the colour and hover tests that follow the redesign
* tests: the merged parameter and narrow toolbar tests follow the compact ribbon
* i18n: the Malay Gap label has an English source and its Japanese and Chinese translations
* apply_off_thread tests: the evaluation lingers in tests, so still computing never depends on machine speed
---------
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
Save As and Open use the browser's file dialogs where the File System Access API exists; Save writes back to the same file, its handle kept in IndexedDB across reloads. File > Download design added. Other browsers keep storing designs in OPFS.
* claim: #3249
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
* inspect.interference/clearance: list mesh bodies as unchecked
Mesh bodies (STL, 3MF and OBJ imports) were filtered out before any pair
was formed, so two overlapping STL imports reported count 0 and an empty
unchecked list, which reads as "no collision". Each mesh body is now
listed in `unchecked` as {a: name, b: null, reason: "mesh body: not
checked"} by both commands. inspect.clearance also stops refusing a mesh
body named in `bodies` or `against` as "no solid body"; it is listed
instead. The parameter docs and the assemblies guide say so.
Fixes#3249
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
* docs: separate the mesh-body note from the paragraph above
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Sonnet 5.5 <noreply@anthropic.com>
While editing a dimension's value, a single click on another driving
dimension now inserts its parameter name (a double-click no longer needed,
and its second click does not insert it twice). A lone value such as `10`
or `10 mm` is replaced by the name; an expression in progress keeps what
was typed and gets the name at the cursor (replacing selected text), so
`10 + ` becomes `10 + d10`. The cursor ends after the name and the field
keeps the keyboard.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* WIP: adopt the saved model on open (#3053)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* WIP: tests
* WIP: bench-open opens as Open does
* docs: opening from the saved model
* Tests: an edit after opening evaluates from the feature it changes
* clippy
* Read SOLIDCRAFT_NO_MODEL_CACHE through the env helper
* Open: no picture from the model when the model itself opens; cancel test evaluates
* Saved model: bodies passed through found without writing their record; states list runs of bodies
* Adopted results go into the evaluation cache: an undone edit, or the marker rolled forward, takes them again
* Model cache size guard: the saved model's writer
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* joint.inspect: what each joint is attached to, for agents
A read-only `joint.inspect {joint?}` gives each joint's definition: for each
side the occurrence, its component and path, the snap as saved, and what
each persistent face/edge name refers to (the feature that made it, and the
sketch and curve a swept side came from), whether the origin resolves and
why not; plus kind, offset, angle, flip, values with limits, expressions,
the motion links it is in, and its solve errors and conflicts. Its id ends
in `.inspect`, so agent gates treat it as reading only.
MCP `inspect_design` includes the definitions when the design has joints
(`joints: false` leaves them out). joint.list and joint.inspect share the
motion-link JSON.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* i18n: catalog entries for Inspect Joint (en, ja, zh)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
`sketch.trim.path {points, dry_run?}` walks a polyline and, at each place it
crosses a curve trim may change, removes that piece exactly as `sketch.trim`
would there, in the order crossed and in one undo step. A piece already gone
is not trimmed again; projected geometry, infinite lines, offset outputs and
pieces trim refuses are passed over (reported in `skipped`). It returns each
trim's result and each removed piece as a polyline; `dry_run` reports them
without changing the design.
With Trim on, a press and drag in the viewport draws that path: the pieces it
would remove light up (a dry run of the command) and letting go runs it. A
click still trims the one piece under it.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Mouse gestures: a ring of tools on the right button, per studio and customizable
Preferences > Navigation gets a Mouse gestures switch and a Customize window (number of
tools and their place, per studio). Gestures need the SolidWorks mouse mode and turn the
right-drag orbit off. The ring is 280/350 pt, one zone per tool, alternating tints (three
when the count is odd). The radial context menu is unchanged.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01Dwcq9eNUMZ1jNeKvWd1bcZ
* Mouse gestures: the ring opens on the right-button press; the right-click menus are off while gestures are on
The ring opens at once on the press, even while a tool or dialog is active. While gestures are
active the viewport's right-click context menu, the right-click that finishes a tool and the
radial context menu no longer fire. With gestures off nothing changes.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01Dwcq9eNUMZ1jNeKvWd1bcZ
* Mouse gestures: the ring opens after 4 px with the right button held; a plain right-click keeps its menu
The ring no longer opens on the press. It opens where the button went down once
the pointer has moved 4 points with the button held, even while a tool is in
progress. A right-click that does not move opens the usual context menu (or
finishes the tool) again; the release that ends a gesture opens no menu. The
radial menu stays off while gestures are active.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01Dwcq9eNUMZ1jNeKvWd1bcZ
* Re-trigger CI (the run was cancelled when approved-for-ci was added)
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01Dwcq9eNUMZ1jNeKvWd1bcZ
---------
Co-authored-by: Claude <noreply@anthropic.com>
* claim: #3324
* Sheet metal: refuse a flat pattern that no longer matches the body
A feature that is not sheet metal can change a sheet body's material
without its sheet model knowing: a mirror combined into it, an extrude
joined onto it, a fillet or chamfer on a corner. The flat pattern, the
DXF and the bend table then wrote the sheet as it was before, a part
other than the one in the design, with no warning.
The evaluator now notes, per sheet, the first such feature: one that
changes the body's shape while its sheet model stays the same. That
feature warns, and sheet.flat_pattern, sheet.export_dxf (also with
per_body) and sheet.export_bend_table refuse with "not supported yet",
naming it. A sheet metal feature, or machining the sheet keeps as
cut-outs, rebuilds the body from the model: it clears the note and
warns that the change is not kept. Moving the body, splitting its faces
and cosmetic threads leave the flat pattern as it is.
* Sheet metal: a modelled thread is refused in the flat pattern too
Only a cosmetic thread leaves a sheet body's material as it is. A
modelled thread cuts the thread profile into the hole, which the flat
pattern does not have, and a later sheet metal feature dropped it
without a word. It now marks the sheet like a fillet does: it warns,
the flat pattern, DXF and bend table refuse naming it, and the feature
that rebuilds the body says the thread is not kept.
The two reliefs that would overlap are still resolved one after the other: the
second one is left out, with a note. The corners come out in flange-index
order, so which of the two keeps its relief depends on the order the flanges
were made in.
Two corners that share an edge never come this far: each relief reaches
exactly r along that edge, and a relief is refused unless 2r fits in it. Two
corners that do not share one can: the square relief at a corner of 120°
reaches 2r from it along the bisector, so at the two 120° corners opposite
each other in a rhombus the two reach each other.
Two reliefs that would overlap are now left out together, each with a note
naming the other, so that which of them is cut does not depend on the order
the flanges were made in.
Fixes#3417.
Co-authored-by: jeremymiribung-blip <jeremymiribung-blip@users.noreply.github.com>
Co-authored-by: Claude Code <noreply@anthropic.com>
The retries in boolean_whole_inner mesh every candidate to compare its
volume. A nudged union at the coarse tolerance could come out with a face
on a cone whose trim loop ran metres along the cone's continuation (edges
up to 12.7 m outside a 155 mm part); meshing it took seconds to minutes per
face and once never finished, though its volume (+-1e10 mm3) failed the
check anyway.
check() first samples the candidate's edges (16 per edge) and discards a
candidate with a point further outside the operands' mesh box than 5% of
their size (or a non-finite point): no edge of a union, cut or
intersection can lie there. The reason goes into the new
BooleanDiagnostics::rejected (omitted from JSON when empty). Results of
sound candidates are unchanged.
On the reporting design the PitchTail join drops from 18.7 s to 4.3 s with
the same result; the regression tests synthesize a cone face whose loop
runs off its surface.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Spike: typed parameter contracts and JSON Schemas for solid.box and solid.extrude
The schema RFC's spike (plan/schema-spike.md). solid.box and solid.extrude get
typed contracts with generated JSON Schemas (2020-12), checked in front of the
unchanged handlers by a per-session level: off (the default, which changes
nothing), warn (the call runs and gains param_warnings) or strict (the call is
refused and the design left alone). Also engine.describe and the MCP tool
describe_command, `solidcraft-cli mcp --param-check off|warn|strict`, a
FeatureResult type for feature replies, and an env-var audit recorder
(SOLIDCRAFT_PARAM_AUDIT) used to check the contracts against every test.
Local spike branch; not for upstream as is (see the results report).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Parameter contracts: put the audit recorder behind a feature; drop two ignored test keys
The audit recorder is now on only in a build with the engine's `param-audit` feature
and `SOLIDCRAFT_PARAM_AUDIT` set. Its code is still compiled, linted and tested without
the feature. `scripts/param_audit.py` summarises a test run's audit logs, and the schema
module's docs give the steps for converting a further command.
Two tests passed keys their command ignores, which the audit found: `position` on
`solid.box` (`hole_face_tests.rs`) and `symmetric` on `solid.extrude` (`face_tests.rs`).
Both are removed, so the tests build what they always did. Comments no longer call
the contracts a spike.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
A line and a circle or arc can now be dimensioned to the circle's edge
(ConstraintKind::LineCircleDistance, saved as line_circle_distance): the gap
while the line misses the circle (0 is tangency), or how far the edge reaches
past the line when it cuts through (stored as `inside`).
Rebased onto main as one commit (the branch's own changes; its merges of main
dropped). Conflicts resolved: the test mod lines in cmd/sketch.rs (both kept,
sorted), and README.md, whose feature list main moved to docs/capabilities.md;
the line-to-circle dimension is listed there now.
Claude-Session: https://claude.ai/code/session_01QWhMwdqJYQKQq8RCLSL1LT
Co-authored-by: jyviko <jyviko@gmail.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Model cache written by default: exact bodies, stored once, scaled caps (#3053)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* bench-open: say why bodies were not kept
* Exact planes and revolutions; budgets for large bodies (#3053)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Native B-rep: rebuild shells as the kernel made them (closed and seam edges) (#3053)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* docs: the model cache and the exact native B-rep (#3053)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* bench-open: time a save without the cache too
* Model cache entries are Deflate-compressed (#3053)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Model cache: one that does not fit the design file is left out, never a failed save (#3053)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Sheet metal: a corner relief no longer depends on the order the corners are cut in
The corner reliefs are planned against the base as it is before any of them is
cut, and the two reliefs at the ends of one edge are compared with each
other. Before, every relief was cut into the base as it went, so the corner
after it saw the relief of the corner before it: the square relief reaches
further from its corner than the round one does (4 / cos(α / 2) against 4), so
on a short edge it was left out where the round one was cut, and which of the
two corners kept its relief depended on the order the flanges were made in.
The reliefs themselves are unchanged: a round about the corner through the
angle the base fills there, or the square with that side (a kite where the
corner is not square, its cuts square to the two edges). What is new is that
they are planned first and cut together, so that a corner's relief depends on
the base and on the other reliefs, and not on the order they are cut in. Two
reliefs that would overlap are still refused, now with a note that says so.
Covered: the four relief shapes at corners of 60° and 120°, with the flanges
of equal and of unequal height, through the kernel and through the engine
(where the flat pattern and the DXF keep one clean loop).
Co-Authored-By: Claude Code <noreply@anthropic.com>
* Sheet metal: cover the corner reliefs at a corner that is not square
The engine and the UI had no test at all for a base whose corners are 60° and
120°: the flat pattern, the DXF, the unfold and the rule manager's own square
relief were all untested there. They work; this says so.
Co-Authored-By: Claude Code <noreply@anthropic.com>
* Sheet metal: say what happens when a corner relief is left out
The guide now says that the reliefs at the corners of one edge are cut
together, and that two of them that would overlap leave the second one out.
A relief that cannot be cut is reported, not dropped.
Co-Authored-By: Claude Code <noreply@anthropic.com>
* Sheet metal: write the corner relief's expected corners out
The engine test hard-coded the corners of the trimmed base; it works them out
instead, and the numbers the test and the sketch share are written with the
precision they need.
Co-Authored-By: Claude Code <noreply@anthropic.com>
---------
Co-authored-by: jeremymiribung-blip <jeremymiribung-blip@users.noreply.github.com>
Co-authored-by: Claude Code <noreply@anthropic.com>
* claim: #2430
* feat: copy saved designs between documents as linked components
* fix: keep occurrence movement controls with their document tab
* test: cover linked design clipboard across tabs
* fix: place linked design pastes at the viewport pointer
---------
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
* claim: #2301
* fix: resolve face context actions from persistent face provenance
* test: cover feature targeting from picked faces
* fix: reveal picked face creators in the Browser
---------
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
* Snapshot: draw a see-through appearance see-through, and give the CLI --body, --tool and --section
A headless picture dropped a body's opacity: the scene carried only a colour, so a design with
a translucent appearance was drawn opaque by `solidcraft-cli snapshot`, by MCP screenshots and
in a design's thumbnail, although the window has always drawn it as glass. There was then no
way to look at the body a cut would remove inside the material it meets: only a volume to
measure and reason about, which hides exactly the errors a picture makes obvious (a tool that
stops short, or lands in the wrong place).
- `SceneMesh` carries the body's opacity; `view::build_scene` takes it from the design
(`model_body_opacity`), and a selected body stays solid so the selection colour reads.
- The GPU capture routes a see-through body into the scene's glass at its own alpha, as the
viewport does; the CPU rasterizer draws the solid bodies first (they own the depth buffer),
then the see-through ones blended over them, far sides before near sides and without writing
depth, so what lies inside shows and a line between the two is not hidden.
- `snapshot --body NAME:opacity=0.3,color=#rrggbb`, `--tool NAME` (that body solid in the tool
colour, the rest see-through) and `--section z=27` run the commands the app itself runs
(`appearance.assign`, `inspect.section`): the options are shortcuts, not a second renderer.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
* Tests: measure the tool colour as it is drawn through a see-through target
The tool-colour filter was derived on paper and demanded a red more than twice either other
channel, which the target in front of it tints away (measured: (200, 108, 85) through opacity
0.3); and the colour check painted the tool, which a solid target hides.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
* fmt
* Snapshot options: strip the colour's # rather than slicing it; README
Slicing `value[1..]` on an input-derived string is what the house rules ask us not to write,
even where a length check has already made it safe. The error a failed assignment reports now
names the body rather than claiming it came from --body, since --tool reaches it too.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
* --tool: assign the bodies around the tool in groups, not one command at a time
Each appearance.assign is an undo step with a document snapshot behind it, so one per body
made --tool cost grow with the size of the design for no reason: the bodies around the tool
all get the same opacity, and the ones that share a colour can be named in one call. A design
whose bodies all wear the default grey now costs two commands whatever its size.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
* Rasterizer: say where its glass and the GPU's differ
Splitting each see-through body by facing orders its own two layers; it does not sort across
bodies, which the GPU does. Worth stating rather than leaving a reader to find it.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5 <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
Christian Svensson